Fitting instructions

​

For best results, mix at least two packs when fitting to avoid repetitions in pattern. We recommend that you always use materials from a single production batch for each installation, as a match between batches cannot be guaranteed. 

​

Clever Click planks or tiles are easily cut using a straight blade in a utility knife. Cut the printside of the plank or tile several times and snap along the line. 

​

The surface beneath the floor must be sufficiently prepared in advance to guarantee successful fitting of the floor covering. In particular, it must be clean, dry, smooth, firm, level, free from defects and not contaminated with grease, oil or chemicals. Clever Click is a 'floating' floor. Never glue or fix the panels to the surface below. The flooring can be installed wall-to-wall, however in large areas or where the floor may be exposed to unusually wide temperature ranges (such as where under floor heating is used, in a conservatory or areas adjacent to a south facing window) then it is advisable to use a 5mm space around the edge, as appropriate .

​

For surfaces larger than 50m2 we advise that an expansion join of 5mm is created around the perimeter of the room, in addition, should a single wall or run be longer than 10 linear metres, then a 5mm expansion joint should be allowed around the perimeter. If you are uncertain of the requirements, please contact your retailer who can confirm the exact requirements. The Clever Click system panels can be joined in two different ways, either tongue-in-groove or groove-in-tongue. The simplest procedure, however, is groove-in-tongue. The advantage of the Clever Click system is that it allows you to choose your own starting position.

 

Moreover, you may work either from left to right or from right to left, whichever is best for you. Depending on the direction in which you work, you are advised to begin from either a corner or a door, it is advisable to begin with the groove side of the plank towards the wall and work from left to right.

 

1) Measure the room to carefully to determine the central axis, from which the first row to be laid is outlined.

 

2) Check whether the first row of panels needs to be narrowed. If not, the lower groove lip of the first row of panels need to be removed. Use of utility knife to neatly cut off the lower groove lip.

​

3) Begin by laying the first row in the corner of the room on your left hand side as you are looking at the wall. Always work from left to right and with the tongue towards yourself.

​

4) Lay the first row in a straight line and click the head ends together. Put the short side of the profile into head end of the previous panel and press the panel downwards. It is recommended to use a rubber mallet for connecting the head ends so that the joint fits securely. Continuing laying the first row in the same way until you get to the last piece.

​

5) For the last piece, measure the last plank to ensure a tight fit to the wall. Then cut away the marked piece and fit the end panel in the same way as the previous panels. When cutting the panel with a utility knife make sure that you cut through the wear layer before breaking the panel.

​

6) For an attractive and natural appearance, we advise you to use the piece left over from row 1 as the first piece in the next row, as long as the remaining piece is at least 1/3 of the total plank length. Repeat for all the subsequent rows.

​

7) For the second row as you did for the first: start on the left side and slide the groove of the panel under an angle of about 25° over the tongue of the previous row and click the groove into the tongue by laying down the panel while pushing it firmly against the first row.

​

8) Then fit the second panel by sliding the groove under at an angle of 25° into the tongue of the previous row. Position the corner of the head end against the previous panel and then drop the short side of the profile into the head end of the previous panel and push downwards. Use a rubber mallet for connecting the head ends so that the joint fits securely. Repeat until you reach the end of the row.

​

9) To ensure a firm Click installation, it is recommended that the planks are tapped together along the long edge with a tapping block and a rubber mallet. This will ensure that the Click mechanism is firmly locked during installation providing a secure joint and avoiding any movement after the installation has been completed.

 

10) To fit the last row of panels you will usually need to narrow them. Do this as follows: lay a panel on top of the previous row with the groove towards the wall, lay another panel upside down up to the edge of the wall and mark the panel underneath. Cut the panel to size and fit the last row.

 

11) Door posts and heating pipes also need to be individually fitted. first cut the panel to the right length. Then place the panel next to the object and draw the correct fitting. Next, cut the panel to size. Doorposts can also be sawn to size if necessary to lay the floor beneath them. For cutting around difficult areas such as door posts, heating pipes and other interior furniture; the use of a Jigsaw with the correct plastic cutting blades is suitable and will avoid unsightly cuts at the perimeter of the room.

​

​

​

​

You have now installed a Clever Click design floor. Your new floor has been produced in accordance with the highest standards and will give you years of pleasure in your home.

​

Although Clever Click design floors are one of the easiest floors to take care of, it is best to follow the recommendations provided below, for optimal protection of the factory finish and to keep your floor looking flesh. 

​

General Floor Maintenance

​

Manual mopping is used for soil removal in small or congested areas (including within large floors) and some mark removal. Spray cleaning may be required for heavier surface marking, (Note: in conditions of heavy soiling, perform a pre-wash by preparing a solution of Xtrafloor Cleaner Maintainer diluted in accordance with the label and prewash heavily soiled areas). 

​

1) Using a two-way bucket mopping system, apply solution using well-wrung mop to remove soiling.

​

2) Mop using overlapping strokes.

​

3) Rinse the mop frequently and change the solution as necessary. 

​

4) Allow entire floor area to dry thoroughly.

​

5) Remove 'Caution' aigna. Ensure all equipment is cleaned thoroughly after use and stored safely. 

​

Tips for dealing with spills:

​

1) Spills of water, grease, food, chemicals and other foreign matter may cause the floor to become slippery.

​

2) Wipe up spills immediately with an absorbent cloth and then wash thoroughly using Xtrafloor Spot Remover as directed on the label or properly diluted Xtrafloor Cleaner maintainer until the spill area is completely clean.

​

3) Allow the floor to dry thoroughly.

​

Notes

​

1) Clever Click products should not be buffed with any pad more abrasive than a red 3M pad (or equivalent).

​

2) Entrance mats, when properly serviced, can effectively remove any abrasive and foreign materials from foot traffic cut down on tracked in water. Clever recommend a minimum of two full strides of entrance matting. 

​

Preventative maintenance

​

1) Place non-rubber doormats at entrances to stop large amounts of dirt from getting indoors.

​

2) Use felt under furniture and chair legs. Rolling office chairs should be fitted with non-rubber casters.

​

3) Clean the floor at least once a week with a vacuum cleaner or mop. You will need to do this more often if you use the floor intensively. 

​

4) We advise that you only use recommended cleaning products, as aggressive cleaning products may damage the floor.

​

5) Stiletto heels can also damage the floor.

​

6) Avoid long-lasting exposure to direct sunlight. Use curtains or blind at peak times to minimise the effect of driect sunlight. Most types of floor discolour under the influence of direct sunlight. To avoid colour discrepancies, you should move the floor coverings present with a certain degree of regularity.